Water Supply Interruption: How to Keep a Business Site Running When the Water Goes Off
TL;DR: A water supply interruption can take a business site from normal to closed within hours, because workplace law requires drinking water, toilets and washing facilities, and food premises need hot and cold running water for handwashing. In England, a business gets £100 when a long planned interruption comes without 48 hours of notice, or when supply is not restored on time. A good plan knows its stored water, watches the incoming main and has an alternative water supply arranged in advance.
Last updated: 5 October 2026
On this page
Key takeaways
- A water supply interruption is any time the supply to your premises is interrupted or cut off, planned or not. The rules in England set notice periods, restoration times and payments for each case.
- For business premises, the payment is £100 if a planned interruption of more than four hours comes without 48 hours of notice, and £100 if the supply is not restored on time, plus £100 for every further 12 hours.
- Workplace law requires drinking water, toilets and washing facilities with hot and cold, or warm, water. Food premises also need hot and cold running water at their handwashing basins.
- Water companies plan an emergency alternative water supply of at least 10 litres per person per day, with priority for vulnerable customers. That is a lifeline, and it will not run a kitchen or a process.
- HSE Legionella guidance says a cold water storage tank should hold only about one day’s use, so on most sites the stored buffer is short by design.
- A flow meter on the incoming main and a level sensor on the tank tell you the moment a loss of water supply starts and how many hours of water are left.
What counts as a water supply interruption?
A water supply interruption is any time the supply of water to your premises is interrupted or cut off, for any reason. The Water Supply and Sewerage Services (Customer Service Standards) Regulations 2008, which set the service standards for customers in England, cover planned works, bursts and emergencies, with different duties for each.
Planned interruptions. When the wholesaler that runs the network turns the water off to carry out necessary works, it must serve notice. Under regulation 17E, the notice has to give the earliest time the supply is expected to go off and the latest time it is expected to come back. If the water is to be cut off for more than four hours, the notice must arrive at least 48 hours before the supply is interrupted.
Unplanned interruptions. Bursts, emergencies and any other loss of water supply fall under a separate duty. The wholesaler must, as soon as reasonably practicable, take all reasonable steps to tell each affected customer that the supply is off, where an alternative supply can be obtained, when it expects to restore it and which telephone number to call for more information.
Low pressure. Pressure has its own standard. Regulation 17G requires a minimum pressure of seven metres static head in the communication pipe serving your premises, which is roughly 0.7 bar. Some sites notice poor pressure first, especially on upper floors and at equipment that needs a minimum inlet pressure.
Some interruptions start on your own side of the boundary. A burst on the supply pipe, a closed valve or a failed booster set looks exactly like a water supply interruption from inside the building, and the water company will not fix it for you. Our guide to customer side leakage explains where that responsibility begins.
How much notice and compensation do businesses get?
In England, a business gets £100 when a planned water supply interruption of more than four hours comes without 48 hours of notice. It also gets £100 if the supply is not restored by the time given in the notice, or within 12 hours of an unplanned interruption, plus £100 for each further full 12 hours without water.
These figures come from regulation 17F of the 2008 Regulations, as amended by the Customer Service Standards (Amendment) Regulations 2025. The higher amounts came into force on 2 July 2025. Domestic customers get £50 for each of the same failures, and business premises get double that.
| Standard | What the wholesaler must do | Payment to business premises |
|---|---|---|
| Notice of planned works | Give at least 48 hours of notice if the water will be off for more than four hours | £100 |
| Restoring the supply | Restore it by the time in the notice, or within 12 hours of an unplanned interruption | £100, then £100 per further 12 hours |
| Pressure | Keep at least seven metres static head in the communication pipe | £50 when pressure falls below it for an hour or more twice within 28 days, up to £250 in a financial year |
Three details matter for business customers. First, in England a business is billed by a retailer while a wholesaler runs the pipes. The regulations make the retailer pay you, and the wholesaler then pays the retailer. Second, restoration payments for a single incident are capped at twice the water supply charges for the affected premises over the 12 months from the day the supply went off. Third, if the provider could not practicably have identified you as affected, you need to claim within three months. There are also exceptions, including drought and circumstances so exceptional that restoring the supply in time could not reasonably be expected.
The payments recognise inconvenience. They are not designed to cover the cost of a closed kitchen, a cancelled clinic or a production line standing still, which is why business continuity planning matters more than the compensation.
Can a workplace stay open without running water?
Only for as long as it can still meet its welfare duties. The Workplace (Health, Safety and Welfare) Regulations 1992 require drinking water, toilets and washing facilities with hot and cold, or warm, water. Food premises also need hot and cold running water at every handwashing basin, so a long water supply interruption quickly becomes a decision about closing.
The duties are specific. Under regulation 22, an adequate supply of wholesome drinking water must be provided for all persons at work. Regulation 20 requires suitable and sufficient sanitary conveniences, and toilets need water to flush. Regulation 21 says washing facilities are only suitable if they include a supply of clean hot and cold, or warm, water, which must be running water so far as is practicable.
Food businesses carry an extra duty. Annex II of the food hygiene regulation 852/2004, which still applies in Great Britain, requires washbasins for cleaning hands to be provided with hot and cold running water. Chapter VII requires an adequate supply of potable water, used whenever necessary to make sure food is not contaminated. For a kitchen, a loss of water supply is a food safety question within minutes.
None of this means every site must close the moment the taps run dry. Bottled drinking water, portable handwashing units and a tank that is still full can buy time. What matters is that someone has decided in advance how long the site can meet these duties, and who calls it when that time runs out. If you run food premises and are unsure, your local authority’s food safety team can advise.

What will the water company provide in an emergency?
A minimum emergency supply, planned per person and prioritised for vulnerable customers. The Drinking Water Inspectorate says water companies must plan to provide an alternative water supply of at least 10 litres per person per day for the first 24 hours of a supply failure, and 20 litres per person per day in a prolonged event.
That planning duty comes from the Security and Emergency Measures Direction 2022, issued under section 208 of the Water Industry Act 1991. It requires water undertakers, in the event of an unavoidable failure of piped water supply, to make sure a minimum supply is provided by alternative means. Their plans must identify and prioritise vulnerable customers and vulnerable sites, and have regard to the needs of non-domestic users as well as domestic users.
The figures themselves appear in the Drinking Water Inspectorate’s guidance on managing insufficient private water supplies, which also points to BS 8551, the code of practice for temporary water supplies and distribution networks.
For a business, the lesson is simple. Ten litres per person per day covers drinking and essential hygiene. It will not run a commercial kitchen, a laundry, a cooling system or a production process, and the plans put vulnerable customers first. If your site needs water to keep trading, your business continuity plan should include your own alternative water supply: a contract with a specialist supplier for bottled water, portable welfare units or water delivered into your storage. Any water put into a tank that feeds drinking or washing outlets must be wholesome, which is why tankering is a job for a specialist.
How long will your stored water last?
About one day of normal use, if the site follows HSE Legionella guidance. HSE advises keeping the volume of cold water storage to a minimum, just enough for one day’s usage, and recording a typical day’s cold water consumption. So the tank is a short buffer by design, and every hour of a water supply interruption counts against it.
The advice comes from HSE’s page on what to consider in hot and cold water systems. It also says stored water should stay below 20 C, and that where there are several tanks they should be linked so water flows through each one, avoiding stagnation. Legionella control pulls towards small, fast-turning cold water storage. Resilience pulls towards more stored water. The way through is to know exactly how much you have and how fast it is going.
Mains-fed and tank-fed outlets behave differently. An outlet fed directly from the incoming main stops the moment the supply stops. An outlet fed from a storage tank keeps running until the tank empties. On many sites that means a drinking water tap goes dry at once while toilets and basins carry on for hours, which can confuse people and delay the call.
Here is a simple illustration. Take a tank holding 6,000 litres on a site that normally uses about 6,000 litres over a working day. If a loss of water supply starts at 8am, the tank lasts roughly until the end of the day at normal use. Close the showers, stop cleaning with water and pause any process use, and it lasts longer. Without a level reading, nobody knows which of those it is.

For the tank itself, see our pages on cold water storage tank monitoring and cold water tank temperature monitoring.
How do you know when the supply has failed?
Watch the incoming main and the storage tank. A water supply interruption shows up as flow on the incoming main dropping to zero during hours when the site normally draws water, and as a tank level that falls without refilling. Both can raise an alert within minutes, long before someone reports that the taps have stopped.
Flow on the incoming main. The AQUAIOT Clamp-on Ultrasonic Flow Meter fits the outside of live pipework from DN8 to DN100, so there is no pipe cutting and no shutdown. On the incoming main it records the flow continuously. A sudden drop to zero in working hours points to a water supply interruption. A sharp rise in flow that is followed by a drop can point to a burst on your own side, which is a job for leak detection.
Level in the storage tank. The AQUAIOT Radar measures the water level in a tank without touching the water. A level that falls and does not recover tells you the refill has stopped, and the rate of fall tells you how many hours of cold water storage are left at the current use.
Alerts that reach a person. The readings feed AQUAIOT’s cloud dashboard, which can send SMS, email and app notifications with role-based routing and escalation rules. That matters at night and at weekends, when the building may be empty. Our guide to water alarm escalation covers how to route an alarm so it is never missed.
A record you can use later. A timestamped flow trace shows when the water stopped and when it came back. That helps when checking whether a restoration deadline was met, and when a claim needs to be made within three months because the provider could not identify you as affected.

What should happen when the water comes back?
A short, planned restart. When the supply returns, check that the tank is refilling, that stored water is back below 20 C, and flush outlets that stood unused during the interruption. HSE advises weekly flushing of infrequently used outlets, to drain and without releasing aerosols, because stagnant water raises the Legionella risk.
HSE’s guidance for landlords puts the principle simply: keep the hot water hot, the cold water cold and keep it moving. It says outlets on hot and cold water systems should be used at least once a week, and that properties left vacant need a flushing regime or other measures, as set out on its page on landlords’ legionella responsibilities.
A water supply interruption of a few hours rarely changes the Legionella picture on its own. A long one, or one that leads to parts of the building being closed, can leave water standing in pipework for days. Build the restart into your plan, with a named person, a flushing list and a place to record temperatures. Continuous Legionella monitoring moves that record from a clipboard to a dashboard.
A seven step plan for a water supply interruption
A good business continuity plan for water fits on one page. It says what stops, how long you have, who decides and what happens next. These seven steps cover what most sites need.
- List what stops without water. Drinking water, toilets, handwashing, kitchens, showers, cleaning, cooling, humidification and any process use. Mark which ones affect your legal duties and which only affect comfort.
- Map mains-fed and tank-fed outlets. Know which outlets stop at once and which run on stored water, so staff are not surprised.
- Know your stored volume and daily use. HSE already asks you to record a typical day’s cold water consumption. Turn it into hours of supply at normal use and at reduced use.
- Set trigger points. Decide in advance at what level or after how many hours you close showers, restrict areas, stop food preparation or close the site.
- Arrange an alternative water supply in advance. Bottled drinking water, portable welfare units or water delivered into storage, from a supplier you have already contracted.
- Monitor the main and the tank. A flow meter on the incoming main and a level sensor on the tank, with alerts going to a named person and escalating if nobody responds.
- Plan the restart and the paperwork. Refill, temperature checks, flushing, records, and any compensation claim within the three month window.
For estates with many buildings, the same plan works best when every site reports into one view. Our guide to multi-site water monitoring explains how to set that up.

How AQUAIOT helps
We help business sites see a water supply interruption the moment it starts, and plan for the hours that follow. A typical deployment puts a clamp-on flow meter on the incoming main and radar level monitoring in the cold water storage, with alerts and escalation set up for the people who make the call.
The meter installs with the system live, so fitting it does not cause the interruption it is meant to catch. The radar reads the tank without touching the water. Both report to a dashboard that keeps the record for compliance, insurance and claims. If you would like to discuss your site, speak to an expert.

Frequently asked questions
Do water companies have to warn businesses before turning off the water?
Yes, for planned works. If the water will be off for more than four hours, the wholesaler must give at least 48 hours of notice, stating when the supply is expected to go off and come back. If it fails to, a business in England is entitled to £100.
How much compensation do businesses get for a water supply interruption?
In England, £100 if the supply is not restored by the promised time, or within 12 hours of an unplanned interruption, plus £100 for each further full 12 hours. Payments for one incident are capped at twice the premises’ water supply charges for 12 months.
Can I keep my office open with no water?
Only while you can still provide drinking water, toilets and washing facilities with hot and cold, or warm, water, as the Workplace Regulations 1992 require. Bottled water and portable welfare units can extend that time. Plan the trigger for closing in advance.
How much water will the water company provide in an emergency?
Water companies must plan to provide at least 10 litres per person per day for the first 24 hours of a supply failure, rising to 20 litres per person per day in a prolonged event, according to the Drinking Water Inspectorate. Vulnerable customers are prioritised.
How long does a cold water storage tank last?
About one day of normal use, if it is sized the way HSE Legionella guidance recommends. The exact time depends on how much the site draws, so a level sensor on the tank and a reduced-use plan turn a guess into a number of hours.
What should I do when the water supply comes back?
Check the tank is refilling, check stored water temperatures are back below 20 C, flush outlets that stood unused, and record what you did. A long interruption that left parts of the building closed needs a fuller flushing regime.
One last thought
Most sites only discover how much they depend on water when it stops. The rules set notice periods, restoration times and payments, and water companies plan for emergencies, but none of that keeps a particular kitchen, clinic or plant room running. That part belongs to the site.
A water supply interruption is one of the easiest disruptions to plan for, because the questions are few and the answers are measurable: how much water you hold, how fast you use it and who hears first when it stops. Answer them before the water goes off, and the next loss of water supply becomes an inconvenience you had already planned for.

