Technology House, Stratfield Park, Waterlooville, PO7 7XN 023 9223 3611
AQUAIOTWorked examples of AQUAIOT systems, set out step by step

Use cases

Each worked example follows one site from the first warning to the parts list.

See what the system measured, what it did and what it saved, minute by minute and with the sums shown. The sites and the figures are examples, not customer installations, so you can judge the same system for your own site.

  • Example sites
  • Sums shown
  • Wiring and parts list
Worked example 01 · Plant room BEXAMPLE
  • A softener hose splits at 12 L/min.LEAK
  • The leak sensor at the low point is wet.WET
  • The relay switches and the valve closes.CLOSED
  • The duty engineer gets a text.TEXT
  • The water stops with 32 L on the floor.STOPPED
  • The engineer resets the controller on site.RESET
With automatic shut-off32 L
With an alarm only3,936 L
Example figures: a 12 L/min leak from 02:12, found at 07:40.
  • TimelineMinute by minute, from the first drop
  • SumsEvery example figure with its arithmetic
  • WiringHow the sensors, controller and valve connect
  • Parts listThe kit we would quote for a similar site
  • Example sitesNot customer installations

About these examples

The sites and the figures are examples, not customer installations.

Each example puts an AQUAIOT system on a realistic site and follows one event from start to finish. The equipment is real and used within its published limits. The site and its figures are examples, and the sums are on the page so every number can be checked. For your own site, we survey it and work out your figures.

  1. 01

    The event is told minute by minute.

    What happened, what the sensors saw and what the system did, in order.

  2. 02

    Every figure comes with its sum.

    Flow rates, times and litres are example figures, and the arithmetic sits beside them.

  3. 03

    The parts are the ones we supply.

    Leak sensors, a controller and a shut-off valve, used within their published limits.

Worked examples

Follow a leak in a plant room from the first drop to the closed valve.

A process water supply in a factory plant room, protected by wired leak sensors, a controller with a relay output and an automatic shut-off valve. The full example replays the night both ways.

Worked example 01
  • Process water
  • Factory plant room
  • Automatic shut-off

A plant room closes its own supply when a hose splits at night.

The problem
A softener hose on a process water supply splits at 02:12 in a plant room that nobody visits at night.
The outcome
The supply closes itself at 02:14, so 32 litres reach the floor instead of 3,936 with an alarm only.
  1. A softener hose splits.
  2. The sensor gets wet and the valve closes.
  3. The water stops at 32 L.
  4. The engineer arrives.
32 Lreach the floor with automatic shut-off.12 L/min for 2 minutes is 24 L, plus about 8 L left in the pipe.
3,936 Lwould reach it with an alarm only.12 L/min for the 328 minutes from 02:12 to 07:40.
Water on the floor through the nightEXAMPLE

07:40Alarm only 3,936 LWith shut-off 32 L

01,0002,0003,0004,00002:0003:0004:0005:0006:0007:0008:00litres02:14 valve closesAlarm only: 3,936 L by 07:40With shut-off: 32 L01,0002,0003,0004,00002:0004:0006:0008:00litres02:14 valve closesAlarm only: 3,936 LShut-off: 32 L
  • Alarm only
  • With automatic shut-off
Point at the chart or drag across it to read any minute of the night. Example figures: a 12 L/min leak from 02:12, a valve that closes at 02:14 and an engineer who arrives at 07:40.

Questions

These are the questions people ask about the worked examples.

Are the worked examples real customer installations?

No. Each worked example uses an example site and example figures, so the whole event and the sums behind it can be shown. The equipment is real: the shut-off valve in the plant room example covers 3/8 to 2 inch pipe and process water up to 5 bar.

Can you work out the same figures for our site?

Yes. Tell us about the supply, the pipe size and where a leak would run. After a survey we set out the sensors, the valve and the rules for your site, with the figures for your own flow rates.

Can the shut-off in the plant room example go on a drinking-water supply?

No. The example is on process water. Fittings on a drinking-water supply have to meet the Water Supply (Water Fittings) Regulations 1999, and we do not offer a WRAS-listed valve with this system. It is for process water, cooling water, wash-down and irrigation lines.

How much does a system like this cost?

Pricing is by quotation, because it depends on the pipe size, the number of sensors and how far the signal has to reach.

Speak to an expert

Tell us about your site and we will work out the same figures for it.

An AQUAIOT engineer will look at the supply, the pipe size and where a leak would run, then set out the sensors, the valve and the rules, with the sums for your own flow rates.

  • Site surveyWe check the supply and the branch before anything is ordered.
  • Figures for your siteFlow rates, times and litres worked out for your own supply.
  • One monitoring partnerShut-off alongside leak detection, flow metering and water quality.

Prefer to talk? Call 02392 233611 or email info@aquaiot.co.uk.

Discuss your site

Takes under a minute. No obligation.

We only use your details to reply to this enquiry.

Shopping Cart (0 items)