Technology House, Stratfield Park, Waterlooville, PO7 7XN 023 9223 3611

The Carbon Footprint of Water: What Estates Should Count, from Supply to Hot Water

TL;DR: Under the government’s 2026 conversion factors, a cubic metre of mains water carries 0.1913 kg CO2e for supply and 0.17088 kg CO2e for treatment when it goes down the drain, about 0.36 kg in total. Heating that same cubic metre from 10°C to 60°C with gas adds at least 10.6 kg, nearly 30 times more. For estates, the carbon footprint of water is mostly the energy used to heat and move it, which is why hot water use and hot water leaks deserve the closest watch.

Last updated: 9 October 2026

Key takeaways

  • The 2026 government conversion factors put mains water supply at 0.1913 kg CO2e per cubic metre and water treatment at 0.17088 kg CO2e per cubic metre, both reported as Scope 3.
  • The supply factor applies to water delivered through the mains; the treatment factor applies to water returned to the sewer through the drains.
  • It takes about 1.16 kWh to warm a cubic metre of water by 1°C, so heating it from 10°C to 60°C takes about 58 kWh before any boiler losses.
  • With gas at 0.18231 kg CO2e per kWh, that heat carries at least 10.6 kg CO2e per cubic metre, nearly 30 times the supply and treatment factors combined.
  • Pumping usually adds far less: moving a cubic metre up 30 metres takes around 0.16 kWh at typical pump efficiencies.
  • A hot water leak of 1 litre a minute can carry about 5.8 tonnes of CO2e a year, against about 0.19 tonnes for a cold water leak of the same size.

What is the carbon footprint of water?

The carbon footprint of water is the greenhouse gas emitted to supply it, treat it after use, and heat or pump it on site. Under the 2026 government conversion factors, mains supply and wastewater treatment together come to about 0.36 kg CO2e per cubic metre. The energy a building uses to heat and move that water is usually far larger.

The factors come from the Department for Energy Security and Net Zero’s greenhouse gas reporting conversion factors 2026, the dataset UK organisations use for carbon reporting. Water supply is 0.1913 kg CO2e per cubic metre and water treatment is 0.17088 kg CO2e per cubic metre, both classed as Scope 3 because the emissions happen at the water company, not on the reporting organisation’s site.

The accompanying methodology paper explains the split. The supply factor accounts for water delivered through the mains network. The treatment factor is used for water returned to the sewage system through the drains. It also notes that the underlying water industry data did not include complete reporting from every company, which adds some uncertainty to both figures.

For most estates, the useful headline is simple: the cold water itself is a small part of the story, and the energy spent on it on site is the large part.

Carbon footprint of water per cubic metre: 0.36 kg CO2e for mains supply and treatment against at least 10.6 kg CO2e to heat it from 10°C to 60°C with gas
The water is cheap in carbon; heating it is not.

How do you calculate the emissions from an estate’s water use?

Multiply the cubic metres supplied by the supply factor, and the cubic metres returned to the sewer by the treatment factor. Then add the energy used to heat and pump water on site, using the fuel and electricity factors. The first part needs good meter data for the conversion factors to work on; the second needs to know how much of the water is heated.

A worked example, using the 2026 factors:

  1. Supply. A site using 10,000 cubic metres a year: 10,000 × 0.1913 = 1,913 kg CO2e.
  2. Treatment. If 9,500 cubic metres return to the sewer: 9,500 × 0.17088 = about 1,623 kg CO2e.
  3. Total water-company emissions. About 3.5 tonnes of CO2e a year, reported as Scope 3.
  4. On-site energy. The gas or electricity used to heat water and run pumps sits in the site’s own energy data, reported under Scope 1 and 2.

The volumes should come from actual meter readings rather than estimates from bills. A bill based on an estimated read, or a meter read only twice a year, can put a year’s water in the wrong reporting period or miss a leak altogether. Continuous metering gives the monthly totals a carbon report needs and shows when a change in use is real.

Why does hot water dominate the carbon footprint of water?

Because heating water takes a lot of energy. Warming one cubic metre by 1°C takes about 1.16 kWh, so taking it from a 10°C mains supply to 60°C takes about 58 kWh. With gas at 0.18231 kg CO2e per kWh, that is at least 10.6 kg CO2e per cubic metre, nearly 30 times the supply and treatment factors.

The 1.16 kWh figure comes from water’s specific heat capacity, about 4.19 kJ per kilogram per degree, so it is physics rather than an estimate. The gas factor of 0.18231 kg CO2e per kWh, gross calorific value, is from the same 2026 conversion factors. A real boiler is less than 100% efficient, so actual emissions are higher; at 90% efficiency the figure rises to about 11.8 kg CO2e per cubic metre.

Electric heating changes the numbers but not the conclusion. At the 2026 UK electricity factor of 0.13096 kg CO2e per kWh, direct electric heating of the same cubic metre carries about 7.6 kg CO2e. A heat pump reduces that in proportion to its efficiency.

The 60°C figure is not arbitrary. The HSE’s Legionella guidance says hot water should be stored at 60°C or more to control Legionella, so the temperature is a safety requirement rather than a comfort choice. That makes reducing the volume of hot water wasted a better lever than cutting the temperature it is stored at.

Carbon per cubic metre of water on an estate: mains supply, wastewater treatment, pumping up 30 metres, and heating from 10°C to 60°C with gas, electric heating shown for comparison
Heating dwarfs every other part of the footprint.

How much carbon does pumping add?

Usually far less than heating. Lifting a cubic metre of water through 30 metres takes about 0.08 kWh of hydraulic energy. Allowing for pump and motor losses at around 50% overall efficiency, that becomes about 0.16 kWh, or about 0.02 kg CO2e at the 2026 electricity factor, roughly 6% of the supply and treatment factors.

Pumping matters more where it runs all the time. Booster sets that cycle through the night, circulation pumps on hot water systems, and pumps running against a leak all use energy for water that does no useful work. The first two are design and control questions; the third is a leak detection question. A booster set that keeps starting through the night, when nobody is drawing water, is often topping up a leak or a valve that does not close, and the pump’s run hours make a useful second check alongside the flow meter.

The hydraulic figure is a straightforward calculation: the energy to lift water equals its weight multiplied by the height. Real pump sets vary widely in efficiency, so a site’s own electricity data for its pumps is the better input when it is available.

Which five sources make up the carbon footprint of water on an estate?

Five sources: mains supply, wastewater treatment, heating, pumping and losses. Supply and treatment are set by the conversion factors. Heating is usually the largest, which is why hot water carbon deserves the first look. Pumping is modest but continuous. Losses, from leaks, overflows and taps left running, multiply all the others, because every lost litre was supplied, often pumped and sometimes heated.

  1. Supply. 0.1913 kg CO2e per cubic metre delivered through the mains.
  2. Treatment. 0.17088 kg CO2e per cubic metre returned to the sewer.
  3. Heating. At least 10.6 kg CO2e per cubic metre heated from 10°C to 60°C with gas.
  4. Pumping. Around 0.02 kg CO2e per cubic metre lifted 30 metres, more where pumps run continuously.
  5. Losses. Every cubic metre lost carries the carbon of every stage it passed through.

The fifth source is the one estates most often miss, because it never appears as a line of its own. It hides inside the metered total, and inside the gas bill for the boilers that heated water nobody used.

Does all the water on a site carry treatment emissions?

No. The treatment factor applies only to water returned to the sewer through the drains. Water that evaporates in a cooling tower, goes into a product, is used for irrigation or soaks into the ground from a leak carries water supply emissions but not water treatment emissions, so an accurate report splits the two volumes.

The split matters most on sites where a large share of water never reaches the drain. A site with cooling towers, a food or drinks process, or large irrigated grounds can overstate its water treatment emissions if it applies the treatment factor to every cubic metre supplied.

The same idea already appears on business water bills. Most sewerage wholesalers assume 90 to 95% of metered water returns to the sewer and charge sewerage on that basis, and sites with more water lost to evaporation or product can apply for a higher allowance. A site that has measured its non-return volume for billing purposes can use the same figure for its carbon report.

Sub-metering makes the split possible. A meter on the cooling tower make-up, the process line or the irrigation supply gives a volume that can be reported with the supply factor alone.

Which year’s conversion factors should a report use?

The factors for the reporting year. The government publishes a new set each summer: the 2026 factors were published on 11 June 2026, with a revised flat-format file in July 2026. For water, the methodology paper says the supply and treatment factors have stayed the same since the 2025 publication.

Using the right year matters more for energy than for water. Electricity factors in particular change from year to year as the generation mix changes, so the heating and pumping part of the carbon footprint of water can move even when the water factors do not.

The simplest discipline is to record volumes and energy use every month from meters, then apply the factors for the year when the report is compiled. Reports built that way can be recalculated if a factor is revised, because the underlying measurements are kept.

Which leaks carry the most carbon?

Hot water leaks, by a wide margin. A leak of 1 litre a minute loses about 526 cubic metres a year. As cold water, that is about 190 kg CO2e for supply and treatment. As hot water heated from 10°C with gas, it is about 5.8 tonnes of CO2e, around 30 times more, before counting the water bill.

Hot water losses take several forms on an estate: a tap or shower left running in an empty building, a leaking hot water pipe in a service duct, a faulty valve returning heated water to drain, or a pressurised heating system that keeps topping itself up because it has a leak. Each wastes energy as well as water.

Cold water leaks still matter. They carry the supply and treatment factors, the pumping energy and the water bill, and on a large estate they are usually the larger volume. Our guide to leak detection ROI shows how to size them, and our water leak detection service covers the sensors and alerts.

Annual carbon of a 1 litre a minute leak: about 0.19 tonnes CO2e as cold water against about 5.8 tonnes as hot water heated with gas
The same leak rate carries 30 times the carbon when the water is hot.

How do you measure the carbon footprint of water instead of estimating it?

Meter three volumes: the water entering the site, the water entering each building or zone, and the cold feed into each water heater or calorifier, which equals the hot water drawn. Multiply each by the right factor, and use continuous readings to catch the losses that turn a small footprint into a large one.

The cold feed is the practical trick. Measuring hot water directly can be awkward, but every litre of hot water drawn is replaced by a litre of cold water flowing into the heater. A meter on that cold feed gives the hot water volume without touching the hot side.

The AQUAIOT Clamp-on Ultrasonic Flow Meter fits the outside of live pipework from DN8 to DN100 with no cutting and no shutdown, so incoming mains, building supplies and heater feeds can be metered without interrupting supply. Continuous readings show the night-time floor, which is where leaks and taps left running show up.

Temperature matters as well. Our Legionella monitoring service tracks temperature profiles at tanks, loops and outlets, which also shows where hot water loops run hotter or colder than they should. For turning the readings into an ESG report, see our guide to water footprint reporting.

Where to meter for water carbon reporting: incoming main, building supplies and the cold feed to water heaters, with the clamp-on flow meter and leak sensor
Meter the cold feed and you have measured the hot water.

Frequently asked questions

What is the carbon factor for water in the UK?

Under the 2026 government conversion factors, water supply is 0.1913 kg CO2e per cubic metre and water treatment is 0.17088 kg CO2e per cubic metre. Both are Scope 3. Supply applies to water delivered through the mains, and treatment to water returned to the sewer.

Is water use Scope 1, 2 or 3?

The emissions from supplying and treating mains water are Scope 3 water emissions, because they happen at the water company. The energy a site uses to heat or pump water is reported in its own Scope 1 or Scope 2 figures, depending on whether it burns fuel on site or buys electricity.

How much carbon does it take to heat water?

About 1.16 kWh warms a cubic metre of water by 1°C. Heating it from 10°C to 60°C takes about 58 kWh, which with gas at 0.18231 kg CO2e per kWh is at least 10.6 kg CO2e before boiler losses, or about 7.6 kg with direct electric heating.

Does fixing leaks reduce carbon emissions?

Yes. Every cubic metre lost carries the supply and treatment factors, and usually pumping energy. Hot water leaks carry the heating energy as well, which makes them around 30 times more carbon-intensive than cold water leaks of the same size.

Where to start

Start with the hot water. Find where water is heated on each site, meter the cold feed into each heater, and compare the night-time flow with what the building should use when it is empty. That single step usually reveals the biggest part of the carbon footprint of water, and the easiest part to cut. Add the incoming main and the largest building supplies next, and the report can be built from measured volumes rather than bills.

To plan metering for water and carbon reporting, tell us about the site and a UK engineer will come back within one working day.

Previous Post
Newer Post
Shopping Cart (0 items)