Technology House, Stratfield Park, Waterlooville, PO7 7XN 023 9223 3611

Calorifier Temperature: What HSE Expects at the Flow, the Return and the Base

TL;DR: HSE guidance in HSG274 Part 2 sets three calorifier temperature targets. The flow from the calorifier should be at least 60 degrees, with the thermostat as close to 60 as practicable without going below it. The return from each circulating loop should be at least 50 degrees, or 55 in healthcare premises. And the whole vessel, including the cooler base, should reach at least 60 degrees for one continuous hour a day, which is what a shunt pump is for. Flow and return are checked monthly.

Last updated: 4 November 2026

Key takeaways

  • HSG274 Part 2 asks for a supply temperature of at least 60 degrees from the calorifier, and its checklist says the thermostat should modulate as close to 60 degrees as practicable without going below it.
  • The return to the calorifier from each loop should be at least 50 degrees, or 55 degrees in healthcare premises, and HSE’s checklist asks for flow and return temperatures to be checked monthly.
  • In indirect calorifiers the cold feed enters at the base, so the water below the heating coil can sit cooler; a timer-controlled shunt pump is used so that the whole vessel reaches at least 60 degrees for at least one continuous hour a day.
  • The calorifier should be inspected internally and cleaned annually, or as indicated by the rate of fouling, and the initial flush from the base checked for clarity, debris and temperature.
  • Standby calorifiers need a procedure to control the risk before they are brought back into service, because stored water that has sat unused is a known Legionella risk.
  • Continuous temperature monitoring on the flow, the return and the base shows the daily hour at 60 degrees actually happening, not just the thermostat setting.
Calorifier temperature targets from HSE guidance: flow at least 60 degrees, return at least 50 degrees or 55 in healthcare, outlets at 50 degrees within one minute, and the whole vessel at 60 degrees for one hour a day
Three numbers and one daily hour do most of the work.

The calorifier is where a building’s hot water is stored and heated, and it is the single most important place to get temperatures right. If it runs too cool, Legionella can grow in the vessel and spread through the loop. If the base never gets hot, sludge and cool water sit there for months. If the return runs cool, the far end of the system is already in the risk band.

This guide explains calorifier temperature in practical terms for duty holders, responsible persons and estates teams: the targets in HSE’s technical guidance HSG274 Part 2, why the base of the vessel matters, what a shunt pump does, which checks are monthly and which are annual, and how continuous monitoring turns a monthly spot reading into a full record.

What temperature should a calorifier be?

A calorifier should store and supply hot water at a temperature of at least 60 degrees. HSE’s technical guidance HSG274 Part 2 asks for a supply temperature of at least 60 degrees from the heat source or storage vessel, and its checklist says the thermostat should modulate as close to 60 degrees as practicable without going below it.

That calorifier temperature is chosen because it controls Legionella in the stored water while keeping scalding risk and energy use as low as practicable. HSE’s guide to managing Legionella in hot and cold water systems puts it simply: hot water storage cylinders (calorifiers) should store water at 60 degrees or higher, and hot water should be distributed at 50 degrees or higher.

The full set of calorifier temperature targets in HSG274 Part 2 is:

PointTargetHealthcare premises
Flow from the calorifierAt least 60 degreesAt least 60 degrees
Return to the calorifier, each loopAt least 50 degreesAt least 55 degrees
Outlets, after running50 degrees within one minute55 degrees within one minute
Whole vessel, including the baseAt least 60 degrees for one continuous hour a daySame
Where more than one calorifierConnected in parallel, each delivering at least 60 degreesSame

Why does the return temperature matter?

The return temperature matters because it shows whether the whole circulating loop is hot, not just the pipe leaving the plant room. HSG274 Part 2 says the circulation pump is sized so that the return temperature to the calorifier is not less than 50 degrees, and asks for a return of at least 50 degrees from each loop, or 55 degrees in healthcare premises.

A good flow temperature with a poor return usually means one of three things.

  1. Poor balancing. HSG274 Part 2 describes balancing the flow and return circuits as critical to avoid long lengths of stagnant pipework that is likely to be at a lower temperature. A leg that gets little flow cools down.
  2. A failing pump. If the circulation pump slows or stops, the loop cools from the far end back towards the plant room.
  3. Heat loss. Missing or damaged insulation, especially in risers and ceiling voids, can pull the return below target on long runs.

Because each loop can behave differently, the guidance asks for the return from each loop, not just a single combined return. A building with three loops needs three return readings.

Why is the base of the calorifier the weak spot?

The base of the calorifier is the weak spot because cold water usually enters there. In an indirect calorifier the cold feed comes in below the heating coil, creating an area where the blended water temperature may support microbial growth, as HSG274 Part 2 describes. Sludge and particles also settle at the base, so it is both the coolest and the dirtiest part of the vessel.

Large vessels can also stratify, with hot water at the top and cooler water in layers below. HSG274 Part 2 says stratification should be avoided, and that fitting a timer-controlled shunt pump to circulate water from the top of the calorifier to the base during the period of least demand should be considered.

Cross-section of an indirect heating calorifier: cold feed and sludge at the base below the heating coil, hot water at the top, and a shunt pump moving hot water from the top to the base
The cold feed and the sludge both sit at the bottom.

What does a shunt pump do?

A shunt pump moves hot water from the top of the calorifier to the base, so the whole vessel heats up evenly. HSG274 Part 2 says it should run when demand is lowest and the vessel is hottest, often in the early hours, with the boiler or other heat source heating at the same time, so that at least 60 degrees is reached throughout the vessel for at least one continuous hour a day.

Four practical points follow from the guidance.

  • Timing. The shunt pump should run during the period of least demand, when the temperature in the calorifier is likely to be highest, often the early hours of the morning.
  • Heat at the same time. The boiler plant or other heat source should be heating while the shunt pump runs, otherwise the pump simply mixes cooler water through the vessel.
  • Clean first. Shunt pump operation should not be started, and no alteration made, before the calorifier has been cleaned and descaled, because the pump may disturb sludge or sediment.
  • Connections. Ideally the shunt pump returns to a connection as low on the vessel as possible. Some calorifiers instead have heating coils that extend to the base to promote mixing.

The test of a shunt pump is not whether it is wired to a timer, but whether the base of the vessel actually reaches 60 degrees for an hour. That needs a temperature reading at the base, and HSG274 Part 2 lists thermometer or immersion pockets on the flow, the return and in the base of the calorifier as appropriate means of measuring temperature.

How often should calorifier temperatures be checked?

HSE’s checklist in HSG274 Part 2 asks for calorifier flow and return temperatures to be checked monthly, and for the calorifier to be inspected internally and cleaned annually, or as indicated by the rate of fouling. The initial flush from the base should be collected annually to inspect its clarity, the quantity of debris and its temperature.

CheckWhat to doHow often
Flow temperatureThermostat as close to 60 degrees as practicable, never belowMonthly
Return temperatureNot below 50 degrees, from each loopMonthly
Internal inspection and cleaningRemove the inspection hatch or use a boroscope, drain and cleanAnnually, or as fouling indicates
Base purgePurge debris to a drain where there is no hatch; inspect the initial flushAnnually, or as the risk assessment indicates
Outlets on non-circulating systems50 degrees within one minute at sentinel points, 55 in healthcareMonthly

The monthly check is the minimum, not a guarantee. A reading taken at 10 o’clock on the first Monday of the month shows the calorifier temperature at that moment. It cannot show a night when the boiler locked out, or a week when the shunt pump timer was wrong. Our guide to Legionella monitoring frequency sets out the full schedule across a water system.

What about standby calorifiers?

Standby calorifiers need a planned procedure before they are brought back into service, because water that has been stored without use can stagnate and cool. HSG274 Part 2 says standby units should be incorporated into routine use safely, that standby pumps should be used at least once each week, and that standby calorifiers need a suitable procedure to control the risk before they return to service.

In practice that means deciding in advance whether a standby calorifier is kept hot and circulated, or drained and isolated, and writing down the steps for bringing it back: heating it to temperature, flushing, checking the calorifier temperature at flow, return and base, and recording the result.

Can you run a calorifier below 60 degrees?

Some systems run calorifiers below 60 degrees using another control, usually a biocide, but HSG274 Part 2 says any reduction should be done in stages, with temperatures reduced only when the alternative is shown to work, and monitoring for Legionella and biocide levels at each stage. In healthcare premises with patients at increased risk, it is currently not permitted.

The pressure to lower temperatures is real. Heat pumps and solar thermal systems work more efficiently at lower temperatures, and every degree costs energy. HSG274 Part 2 says calorifiers attached to solar heating systems should be managed, monitored and maintained to achieve the same flow temperatures as conventionally heated calorifiers throughout the year, and warns that when there is little heat gain from the panels a larger volume may sit at a reduced temperature. If you are considering a lower calorifier temperature, it is a decision for your risk assessment and your competent advisers, not a thermostat change.

How do you balance Legionella control and scalding?

You balance Legionella control and scalding by keeping the calorifier at 60 degrees and the system hot, and controlling the temperature at the point of use where people are at risk. HSE says that where vulnerable people are at risk from scalding during whole body immersion, water temperatures must not exceed 44 degrees, and that baths and showers should be fitted with thermostatic mixing valves in those settings.

HSE’s page on scalding and burning in health and social care adds that outlet temperatures and thermostatic mixing valves should be monitored and maintained. The calorifier temperature and the outlet temperature are therefore two different targets for two different risks, and both need checking. Our guide to TMV temperature monitoring covers the valve side.

What is thermal disinfection?

Thermal disinfection is a way of cleaning a hot water system by raising the temperature of the whole calorifier contents and circulating water for at least an hour, then flushing every outlet. HSG274 Part 2 says the calorifier temperature should be high enough that the outlets do not fall below 60 degrees, and each tap and appliance should run for at least five minutes at full temperature, measured and recorded.

The guidance also warns that thermal disinfection may prove ineffective where parts of the calorifier or system fail to reach the required temperature for long enough. That is another reason to measure the base and the far end of the loop, not just the flow pipe.

How does continuous monitoring help?

Continuous monitoring helps by recording the calorifier temperature at the flow, the return and the base every few minutes, so you can see whether the vessel reached 60 degrees for its daily hour, whether the return stayed above 50 degrees overnight, and exactly when a problem started. It turns a monthly snapshot into a complete record with alerts.

AQUAIOT’s automated Legionella monitoring places wireless temperature sensors at tanks, calorifiers, loops and sentinel outlets. Readings are timestamped and logged to the cloud over cellular or LoRaWAN telemetry, thresholds are checked against HSE guidance, and an alert goes by SMS, email or app when hot water falls below 50 degrees at the point of use or a scheduled flush is missed. Records are tamper-evident and can be exported, or sent to CAFM and BMS systems through RS485, Modbus or an API, and sensors fit without pipe cutting or a shutdown.

For a calorifier, three sensors answer most questions.

  • Flow. Shows that the thermostat holds at least 60 degrees through the day, and catches a boiler lockout at night.
  • Return. Shows each loop staying above 50 degrees, and catches a failing circulation pump or a poorly balanced leg.
  • Base. Shows whether the shunt pump hour actually reaches 60 degrees at the bottom of the vessel.

Our page on calorifier temperature monitoring describes the set-up in more detail, and Legionella monitoring requirements in the UK explains how it fits ACoP L8.

Illustrative 24-hour calorifier trace: flow steady above 60 degrees, return above 50 degrees, and the base rising to 60 degrees during the early-morning shunt pump hour
The base trace is the one that shows the daily hour really happened.

What mistakes do sites make with calorifier temperature?

The most common mistakes are trusting the thermostat dial instead of a measurement, checking only the flow and never the return or base, running a shunt pump without heat, starting a shunt pump on a dirty vessel, and leaving standby calorifiers without a procedure. Each one leaves part of the system cooler than the records suggest.

  • Trusting the setting. A thermostat set to 60 degrees is not a calorifier at 60 degrees. Measure it.
  • Flow only. A hot flow with a cool return means part of the loop is in the risk band.
  • One return for several loops. The guidance asks for each loop.
  • Shunt pump without heat. Mixing without heating can lower the top temperature without raising the base.
  • Shunt pump on an uncleaned vessel. It can stir sludge through the system.
  • Forgotten standby units. A standby calorifier needs its own procedure before it returns to service.
Monthly and annual calorifier checks from HSG274 Part 2: flow and return temperatures monthly, internal inspection and cleaning annually, and the base flush inspected annually
Monthly temperatures, annual inspection.

Frequently asked questions

What temperature should a calorifier be set at?

HSE guidance asks for a calorifier supply temperature of at least 60 degrees, with the thermostat modulating as close to 60 degrees as practicable without going below it. The whole vessel should reach at least 60 degrees for one continuous hour a day.

What should the calorifier return temperature be?

The return to the calorifier from each circulating loop should be at least 50 degrees, or 55 degrees in healthcare premises, according to HSG274 Part 2. A low return usually points to poor balancing, a failing circulation pump or heat loss.

How often should calorifier temperatures be checked?

HSG274 Part 2 asks for calorifier flow and return temperatures to be checked monthly, with internal inspection and cleaning annually or as fouling indicates. Continuous monitoring records them all the time and alerts when they drift.

Why does a calorifier need a shunt pump?

Because cold water enters at the base and the vessel can stratify, the base may stay cooler than the top. A shunt pump moves hot water down so the whole vessel reaches at least 60 degrees for one continuous hour a day, with the heat source running at the same time.

Can a calorifier be run at 55 degrees?

Only as part of a risk-assessed alternative control, usually a biocide, introduced in stages with monitoring for Legionella and biocide levels. HSG274 Part 2 says it is currently not permitted in healthcare premises where patients are at increased risk.

How long should a calorifier be at 60 degrees each day?

HSG274 Part 2 says the heat source should be heating while the shunt pump runs, so that a temperature of at least 60 degrees is achieved throughout the vessel for at least one continuous hour a day.

Where to start

Look at your last three months of calorifier records and check that they include the return from each loop, not just the flow, and ask whether anyone has ever measured the base during the shunt pump hour. If you want those readings every few minutes with alerts, contact AQUAIOT with the number of calorifiers and loops on site, and we will suggest where temperature sensors should go.

Previous Post
Newer Post
Shopping Cart (0 items)